BackgroundThe friction and wear performance of wet clutches and other devices of this type can
WhatsApp : +86 13816217984
Email : info@qinsun-lab.com
The friction and wear performance of wet clutches and other devices of this type can be improved by attention both to the lubricant and the friction material used. In 1995 a Japanese Standard was introduced, describing a method of determining the friction characteristics of various production clutch plate components.
Other test methods include the LVFA and the SAE#2 machines. The former uses small scale parts, manufactured from the friction material, and uses a flywheel coast-down to achieve a full range of sliding speeds. The SAE#2 machine tests a full clutch pack and, while giving an overall performance of the clutch/lubricant system, does not give detailed knowledge of friction characteristics or the influences of wear of the components.
The STD-TE 92M Automated Clutch Friction Test Machine offers just that possibility. It uses a single friction pair in their original manufactured state. The machine may be configured to accept clutch plates from North American, European and Japanese manufacturers by fitting appropriate clamps STD-TE 92M/FPC. Clutch plates up to 11.25 inch (286 mm) diameter may be accommodated.
The machine may also be used to test limited-slip differential, synchromesh and torque converter components with custom design modifications. The machine can be supplied with test adapters to conform to the JASO M349 standard.
| Specimen Size: | Mean radius of friction material: 35 to 125 mm (typical) |
| Maximum outer diameter: 286 mm | |
| Small Size Specimen: | Mean radius of friction material: 15 mm (typical LVFA) |
| Speed Turn-Down Ratio: | 100:1 |
| Machine Torque/Speed: | 37.5 Nm @ 1.000 rpm |
| 18.7 Nm @ 2.000 rpm | |
| 224 Nm @ 167 rpm | |
| 112 Nm @ 333 rpm | |
| 50% over-current capacity for 30 seconds | |
| Low Load: | 50 to 1.000 N (LVFA specimens) |
| High Load: | 250 to 10.000 N (CLUTCH specimens) |
| Torque Transducer: | strain gauge beam |
| Range: | 1.000 N |
| Torque Arm Radius: | 187 mm |
| Torque Range: | 180 Nm |
| Heater Power: | 3 kW |
| Method: | electrical resistance heaters |
| Temperature Range: | 40 to 200°C (100 to 400°F) |
| Temperature Sensor: | K-type thermocouple |
| Motor: | 4 kW, 4-pole ac with 1024 pulse per rev shaft encoder |
| Interface: | Serial Link Interface Module |
| Software: | COMPEND 2000 |
| TE 92M/CSM Coolant Service Module | |
| Circulating Fluid: | heat transfer oil |
| Feed Pump: | positive displacement gear pump |
| Pump Power: | 0.37 kW |
| Flow Rate: | 4 litres/minute maximum |
| Control Valve: | 3-way electro-pneumatic |
| Controlled Parameters | Rotational Speed |
| Temperatures | |
| ふか | |
| テスト期間 | |
| Recorded Parameters | ふか |
| Rotational Speed | |
| Friction Torque | |
| Temperatures | |
| テスト期間 | |
| Friction Coefficient | |
| Services | |
| Electricity: | 380/415 V, three phase, 50/60 Hz, with neutral and earth 7.5 kW |
| Clean, dry air: | 4 cfm at 8 bar (120 psi) |
| Mains water and drain: | 10 l/min (typical) |
| Installation | |
| Floor-standing machine: | 600 mm x 800 mm deep x 1.000 mm high, 400 kg |
| Coolant service module: | 930 mm x 530 mm x 500 mm high, 50 kg |
免責事項: 上記のコンテンツは,業界内部者のみの参照およびコミュニケーションのためであり,その正確性または完全性を保証しません.関連法規および本ウェブサイトの規制により,関連品を購入するユニットまたは個人は,有効な資格および資格条件を取得する必要があります.
会社電話
+86-21-6420 0566
営業時間
月曜日から金曜日
携帯電話:
13816217984
メール：
info@qinsun-lab.com
